Overview:

With Pioneer Aero's Craig Cunha and Doug Brown having begun permanently riveting the SBD's Wing Center Section together, as covered in the previous restoration update, it was time for Rod Hanson to start forming and installing plumbing for the various systems which run through the airframe. This includes lines for the hydraulic, fuel, electrical and indicating systems. This article will cover the first steps in this process.

Landing Gear Position Indicator Conduits:

While it may seem innocuous-looking at first glance, especially given its location in the cockpit just outboard of the lefthand rudder pedal support, the SBD's landing gear position indicator plays an important role in flight safety. As the image reveals, the gauge shows the positional status of each main undercarriage leg: up, down, or somewhere in between!

The landing gear position indicator for the SBD's main undercarriage is shown here in the pilot's cockpit. A separate cable is linked to each of the two main undercarriage legs. When a gear leg deploys or retracts, the cable will shift the marker on this indicator to let the pilot know its position on the cycle. In the case of this particular SBD-6, which belongs to the National Air & Space Museum, the main undercarriage legs are shown to be in the stowed position (UP), which is correct as the aircraft was displayed in an airborne configuration at the time.  (image cropped from NASM photograph of their collection's SBD-6 captured by Eric Long/Mark Arvino on July 29, 2007)
The landing gear position indicator for the SBD's main undercarriage is shown here in the pilot's cockpit. A separate cable is linked to each of the two main undercarriage legs. When a gear leg deploys or retracts, the cable will shift the marker on this indicator to let the pilot know its position on the cycle. In the case of this particular SBD-6, which belongs to the National Air & Space Museum, the main undercarriage legs are shown to be in the stowed position (UP), which is correct as the aircraft was displayed in an airborne configuration at the time. (image cropped from NASM photograph of their collection's SBD-6 captured by Eric Long/Mark Arvino on July 29, 2007)

Unlike most modern aircraft, the spring-loaded indicators on this gauge are directly connected by cables (actually solid wires) to each undercarriage leg. So when a gear leg cycles up or down, the corresponding indicator's spot on the gauge face precisely tracks the given leg's physical position. As a result, unless a cable is severed, the pilot will always know whether the aircraft's undercarriage is in the correct position for the desired flight operation.

The landing gear position indicator cables reach down from the cockpit into the Wing Center Section and then run out to their respective landing gear legs through a dedicated conduit, one for each cable. These conduits are formed from metal tubing, and fabricated much like other aircraft plumbing. They run most of their length along the rear face of Spar #1 and help ensure the cables don't snag on anything during their operation. Pioneer Aero's Rod Hanson refabricated and installed these two conduits for our Dauntless, with the following images describing some of his work.

This image shows a broader view of the righthand landing gear leg position indicator conduit as it snakes its way through the ribs spanning Spars #1 and #2.  Note the circular, copper-colored component attached to Spar #1 which the conduit crosses over at image right; this is a bushing through which the SBD’s righthand main landing gear leg pivots. Unlike the previous two images, this shot was captured after the Wing Center Section structure, from Spar #2 on back, had been removed for painting and preparation for final assembly. (image via Pioneer Aero Ltd.)
This image shows a broader view of the righthand landing gear leg position indicator conduit as it snakes its way through the ribs spanning Spars #1 and #2. Note the circular, copper-colored component attached to Spar #1 which the conduit crosses over at image right; this is a bushing through which the SBD’s righthand main landing gear leg pivots. Unlike the previous two images, this shot was captured after the Wing Center Section structure, from Spar #2 on back, had been removed for painting and preparation for final assembly. (image via Pioneer Aero Ltd.)

Main Undercarriage Brake Lines:

While Rod Hanson was working on the landing gear leg position indicator conduits, he also began fabricating and installing hydraulic brake lines for the main undercarriage. The sections he installed run from the swivel joint attached to the rear face of the Nose Spar and trace along that spar into the wheel well. The following images describe some of Hanson's efforts in this area.

This image shows the hydraulic brake line for the lefthand main undercarriage wheel during its installation. The hydraulic line is seen running from right to left along the rear face of the Nose Spar, before it ducks through a lightening hole to connect with the opposite side of the grey anodized swivel fitting at image left. Note the elbow joint on the swivel fitting. This port rotates freely in synch with the undercarriage leg, allowing it to connect directly to a rigid hydraulic line running down the main landing gear leg to the disc brakes, negating any need for a flexible hose to perform the same task. (image via Pioneer Aero Ltd.)
This image shows the hydraulic brake line for the lefthand main undercarriage wheel during its installation. The hydraulic line is seen running from right to left along the rear face of the Nose Spar, before it ducks through a lightening hole to connect with the opposite side of the grey anodized swivel fitting at image left. Note the elbow joint on the swivel fitting. This port rotates freely in synch with the undercarriage leg, allowing it to connect directly to a rigid hydraulic line running down the main landing gear leg to the disc brakes, negating any need for a flexible hose to perform the same task. (image via Pioneer Aero Ltd.)
This image shows both the partially installed brake line for the lefthand wheel running along the white-painted Nose Spar and also the conduits for the left and righthand landing gear position indicator cables, which are visible running along the rear face of Spar #1 (painted green) and passing up through the upper wing skin towards where the cockpit will be. (image via Pioneer Aero Ltd.)
This image shows both the partially installed brake line for the lefthand wheel running along the white-painted Nose Spar and also the conduits for the left and righthand landing gear position indicator cables, which are visible running along the rear face of Spar #1 (painted green) and passing up through the upper wing skin towards where the cockpit will be. (image via Pioneer Aero Ltd.)